「Asterisk pjsip」の版間の差分
提供: VoIP-Info.jp
(→エンドポイント(電話機)) |
(→基本設定) |
||
64行目: | 64行目: | ||
outbound_auth = phone1 | outbound_auth = phone1 | ||
aors = phone1 | aors = phone1 | ||
+ | ==Wizard== | ||
+ | Asteriskにはpjsip_wizardが組み込まれており、PjSIPの設定を簡素化することができます。使う条件は以下の通りです。 | ||
+ | *基本の設定はpjsip.confに書く | ||
+ | :transportなどの情報はpjsip.confに書く必要があります | ||
+ | *Wizard用のファイル名はpjsip_wizard.conf | ||
+ | *共通化したテンプレート内で各セクションを指定するにはスラッシュ(/)で区切る | ||
+ | :例: endpoint/dtmf_mode | ||
+ | 記述例 | ||
+ | ;電話機用テンプレート(共通設定) | ||
+ | [phone-defaults](!) | ||
+ | type=wizard | ||
+ | transport = transport-udp | ||
+ | accepts_registrations = yes | ||
+ | sends_registrations = no | ||
+ | accepts_auth = yes | ||
+ | sends_auth = no | ||
+ | endpoint/context = default | ||
+ | endpoint/dtmf_mode = rfc4733 | ||
+ | endpoint/call_group = 1 | ||
+ | endpoint/pickup_group = 1 | ||
+ | endpoint/language = ja | ||
+ | endpoint/disallow = all | ||
+ | endpoint/allow = ulaw | ||
+ | endpoint/rtp_symmetric = yes | ||
+ | endpoint/force_rport = yes | ||
+ | endpoint/direct_media = no | ||
+ | endpoint/send_pai = yes | ||
+ | endpoint/send_rpid = yes | ||
+ | endpoint/rewrite_contact = yes | ||
+ | endpoint/inband_progress = yes | ||
+ | endpoint/allow_subscribe = yes | ||
+ | aor/max_contacts = 1 | ||
+ | aor/qualify_frequency = 30 | ||
+ | aor/authenticate_qualify = no | ||
+ | |||
+ | ;各電話機個別設定 | ||
+ | [phone1](phone-defaults) | ||
+ | inbound_auth/username = phone1 | ||
+ | inbound_auth/password = mypasswordishere |
2018年10月23日 (火) 11:58時点における版
AsiteriskでチャネルにPjSIPを使用する際の設定方法など
コンパイル
Asterisk 13以前ではpjprojectを別個インストールするか、configureに--with-pjproject-bundledを付けて実行する必要がありましたが、Asterisk 16からはデフォルトでbundledインストールされるようになりました。
各バージョン毎のインストール方法についてはAsteriskのそれぞれのページを参照してください。
Asterisk 13
Asterisk 16
基本設定
グローバル設定
pjsip.confに書きます。基本で必要なものは以下です。
[general] maxexpirey = 3600 [transport-udp] type = transport protocol = udp bind = 0.0.0.0:5070
sip.confに書いていたものと同じですが、トランスポートはセクションで明示指定します。上の例では5070ポートにbindさせていますが、5060を使用する場合にはここを5060にします。
なお、他の設定ファイル同様に#includeは使えます。なので、電話機と回線は別ファイルにした方が見通しは良いかも。
Wizardおよびテンプレート(!)も使えます。
ACL
ACLの例は次の通りです。
[acl] type=acl deny=0.0.0.0/0.0.0.0 permit=192.168.0.0/255.255.0.0
※deny,permitはこの順でないとpermitしてdenyしてしまう模様で、逆に書くと誰も使えなくなります。
エンドポイント(電話機)
エンドポイントを設定する場合にはセクションが3つ必要です。エンドポイントそれ自体とaor,authの3つです。
[phone1] type = aor max_contacts = 1 qualify_frequency = 30 authenticate_qualify = no [phone1] type = auth username = phone3 password = mysecretpassword [phone1] type = endpoint context = default transport=transport-udp dtmf_mode = rfc4733 disallow = all allow = ulaw allow = alaw rtp_symmetric = yes force_rport = yes rewrite_contact = yes direct_media = no send_pai = yes inband_progress = yes call_group = 1 pickup_group = 1 language = ja device_state_busy_at = 1 auth = phone1 outbound_auth = phone1 aors = phone1
Wizard
Asteriskにはpjsip_wizardが組み込まれており、PjSIPの設定を簡素化することができます。使う条件は以下の通りです。
- 基本の設定はpjsip.confに書く
- transportなどの情報はpjsip.confに書く必要があります
- Wizard用のファイル名はpjsip_wizard.conf
- 共通化したテンプレート内で各セクションを指定するにはスラッシュ(/)で区切る
- 例: endpoint/dtmf_mode
記述例
- 電話機用テンプレート(共通設定)
[phone-defaults](!) type=wizard transport = transport-udp accepts_registrations = yes sends_registrations = no accepts_auth = yes sends_auth = no endpoint/context = default endpoint/dtmf_mode = rfc4733 endpoint/call_group = 1 endpoint/pickup_group = 1 endpoint/language = ja endpoint/disallow = all endpoint/allow = ulaw endpoint/rtp_symmetric = yes endpoint/force_rport = yes endpoint/direct_media = no endpoint/send_pai = yes endpoint/send_rpid = yes endpoint/rewrite_contact = yes endpoint/inband_progress = yes endpoint/allow_subscribe = yes aor/max_contacts = 1 aor/qualify_frequency = 30 aor/authenticate_qualify = no ;各電話機個別設定 [phone1](phone-defaults) inbound_auth/username = phone1 inbound_auth/password = mypasswordishere